Build a toy heat pump
Two buckets of water, a small compressor like the one in a fridge, an expansion valve and two copper coils. Put the parts in the right places and switch it on: one bucket gets hot while the other gets colder, until it starts to freeze. Then change the parts and see what happens.
1. Build it
Drag a part onto one of the four dashed places, or tap a part and then a place. Tap a placed part to take it back. The refrigerant flows clockwise, in the direction of the arrows.
Parts box
2. Run it
3. Experiments to try
- Watch the COP fall. At the start both buckets are at the same temperature and the COP is high. As the gap between them grows, the heat pump has to push heat further "uphill" and the COP drops. That is why a heat pump works best with low radiator temperatures.
- Small coils or large coils? Build it with the small coils, then with the large ones. Larger coils need a smaller temperature difference to pass the same heat, so the refrigerant can condense at a lower temperature and evaporate at a higher one: the COP goes up.
- A bigger compressor. The large compressor heats faster but with a lower COP, and with small coils the pressure climbs until the safety switch stops it.
- Freeze the cold bucket. When the cold water reaches 0 °C it stays there while ice forms: freezing water gives up a lot of heat (334 kJ for every kilogram), so the heat pump keeps working on "free" heat from the ice.
- Foam boxes. Open buckets swap heat with the room, so the hot one stops rising and the cold one warms up again when the compressor stops. Insulate them and compare.
- Build it backwards. Swap the compressor and the valve. Now the left bucket gets hot. Air conditioners that also heat do exactly this, with a four-way valve that reverses the flow.
4. Try it for real, safely
You can feel every part of the heat pump idea at home, without opening any machine.
Squeeze it: a bicycle pump
Cover the outlet of a bicycle pump with your finger and pump hard ten times. Feel the bottom of the pump: it is warm. Squeezing a gas heats it, just like the compressor heats the refrigerant.
Let it go: a rubber band
Stretch a thick rubber band quickly and touch it to your lip: it feels warm. Hold it stretched for ten seconds, let it go quickly and touch it again: it feels cool. Releasing it takes in heat, like the refrigerant after the valve.
Your fridge is a heat pump
Put a thermometer in the fridge and another next to the coil at the back (or underneath). Inside is about 5 °C, the back is warm: heat is being pumped out of the food into the kitchen. A plug-in energy meter shows how little electricity that takes.
A solid-state heat pump (with an adult)
A Peltier module is a small tile that pumps heat from one side to the other when electricity flows through it, with no moving parts. Put a cup of water on each side, run it from a 12 V supply for a few minutes and measure both cups: one warms, one cools. Always keep the hot side on a heat sink or in water, or it overheats in seconds.
5. Shopping list: build the toy for real
There are three ways to build a real two-bucket heat pump and measure its COP. Prices are rough guides in euros (2026); shop around.
A. Ready to use: a sealed school heat pump
The closest thing to the toy. Educational suppliers sell demonstration heat pumps with a small compressor, an expansion valve, two copper coils in water containers, pressure gauges and a sight glass, filled with refrigerant and sealed at the factory. You never touch the refrigerant.
- Heat pump demonstrator for schools, sealed and pre-filled (search for "heat pump demonstrator" at physics teaching suppliers) — about €900–2,500
- Two digital thermometers with probes — about €10–25 each
- A plug-in energy meter, to read the electricity used — about €15–30
- A measuring jug and a stopwatch (a phone will do)
Best for a school: ask your physics department, many already have one.
B. The toy from parts (refrigerant work by a technician)
Exactly the parts in the toy. You can buy and arrange them, but joining the pipes, testing for leaks, pulling a vacuum and filling the refrigerant must be done by a certified refrigeration technician: the law requires it, and the gas is under high pressure and can be flammable.
- Compressor: a small hermetic fridge compressor, about 1/8 hp (80–100 W), for R290 or R134a — about €60–150
- Two coils: soft copper refrigeration tube, 6 mm (1/4"), about 3 m for each coil, wound around a bottle — about €25–40
- Expansion valve: a capillary tube matched to the compressor (or a small thermostatic expansion valve) — about €5–60
- Filter drier, which keeps moisture out of the circuit — about €5–15
- Sight glass, to watch the refrigerant bubble and turn liquid — about €10–20
- Two pressure gauges (high and low side) with access valves — about €30–60
- High-pressure safety switch, the same job as in the toy — about €15–30
- A wooden board to mount it on, two 5 L buckets or foam boxes, two thermometers and an energy meter
- The technician's work: brazing, pressure test with nitrogen, vacuum and charging (a few hundred grams of refrigerant) — ask for a quote
C. Build it yourself: a Peltier heat pump (with an adult)
No refrigerant and no compressor: a Peltier module pumps heat electrically. It is less efficient than a compressor, but it tests the same idea with two buckets, and you can build it on a kitchen table in an afternoon.
- Peltier module TEC1-12706 (12 V, about 6 A), get two in case one breaks — about €5–10 each
- Two aluminium water blocks, 40 × 40 mm (sold for PC water cooling) — about €5–10 each
- Two small 12 V submersible pumps and 2 m of silicone tube that fits them — about €10–20
- 12 V power supply, at least 10 A, with screw terminals — about €20–30
- Thermal paste and two small clamps or bolts to press the sandwich together — about €5–10
- DC power meter (volts, amps, watts) between the supply and the module — about €10–20
- Two insulated containers (foam boxes or 2 L food flasks), two thermometers, a measuring jug
How to put it together: paste one water block on each face of the Peltier module and clamp them. Put a pump in each container and run its water through one block and back. Fill both containers with the same amount of water at the same temperature, switch on the pumps, then the module. One container warms and the other cools.
Never run the module without water flowing on its hot side: it burns out in seconds. Keep the electrics away from the water and dry your hands.
Measure your COP
Write down the water's mass (1 litre is 1 kg), both temperatures every 5 minutes, and the electricity. Then:
electricity (kJ) = watts × seconds ÷ 1000 (or kWh × 3600)
COP = heat into the hot bucket ÷ electricity
Example: 5 kg of water warming by 10 °C takes in 5 × 4.19 × 10 = 210 kJ. If the meter shows 80 W for 20 minutes, that is 80 × 1200 ÷ 1000 = 96 kJ, so COP = 210 ÷ 96 = 2.2. Measure in the first half hour, before the buckets swap much heat with the room, and compare with the toy above. A Peltier module will give a heating COP of about 1.2–2; a compressor about 2–4.
The toy above is idealised: the compressor's power is held fixed, the coils have a fixed size, and pressure drops are left out. Its refrigerant cycle is computed with the same CoolProp property tables as the full designer.